Taking aside your Xbox One may look like a frightening activity, nevertheless it’s truly fairly easy in case you have the fitting instruments and directions. Whether or not you are seeking to improve your console, repair a {hardware} challenge, or just clear out the mud bunnies, this step-by-step information will assist you to disassemble your Xbox One safely and effectively.
Earlier than you start, collect the mandatory instruments: a Phillips #0 screwdriver, a T8 Torx screwdriver, and a spudger. You may additionally want a clear work floor and a bowl or container for storing the screws. After getting your instruments and workspace prepared, energy down your Xbox One and unplug all of the cables.
To begin, flip the console the wrong way up and take away the rubber ft on the underside. This can reveal the screws that maintain the underside cowl in place. Use your Phillips #0 screwdriver to take away the screws, then elevate off the underside cowl. Subsequent, use your T8 Torx screwdriver to take away the screws that safe the facility provide unit to the chassis. As soon as the screws are eliminated, you may fastidiously elevate out the facility provide unit. From right here, you may proceed disassembling the Xbox One by eradicating the optical drive, motherboard, and different inner elements. Simply remember to take your time and comply with the directions fastidiously, and you will have your Xbox One aside very quickly.
Disassembling the Console
Earlier than you start disassembling the console, be sure it’s turned off and the facility twine is disconnected. You will have a T8 Torx screwdriver for this step.
First, take away the 2 screws on the underside of the console, close to the entrance edge. Then, take away the 2 screws on the again of the console, close to the highest edge. These screws safe the underside panel to the remainder of the console.
As soon as the screws are eliminated, you may gently elevate the underside panel away from the console. Watch out to not harm any of the wires or cables which can be linked to the underside panel.
Eradicating the Energy Provide
The ability provide is positioned at the back of the console. It’s held in place by 4 screws. Take away these screws after which gently elevate the facility provide out of the console.
Watch out to not harm any of the wires or cables which can be linked to the facility provide.
As soon as the facility provide is eliminated, you may disconnect the wires which can be linked to it. The wires are color-coded, so it’s simple to reconnect them if you reassemble the console.
Here’s a desk of the wires which can be linked to the facility provide:
| Wire Shade | Connector |
|---|---|
| Black | Floor |
| White | -12V |
| Orange | +12V |
| Purple | +5V |
Eradicating the Motherboard
Now that the Xbox One is in items, it is time to take away the motherboard. The motherboard is the center of the Xbox One, and it accommodates the entire vital elements, together with the CPU, GPU, and RAM. To take away the motherboard, you may have to:
- Disconnect the entire cables which can be linked to the motherboard.
- Take away the screws which can be holding the motherboard in place.
- Raise the motherboard up and take away it from the Xbox One.
- Watch out when eradicating the motherboard, as it’s a delicate element.
| Software | Objective |
|---|---|
| Torx screwdriver | To take away the screws that maintain the motherboard in place |
| Phillips screwdriver | To take away the screws that maintain the cables in place |
| ESD wrist strap | To forestall electrostatic harm to the motherboard |
As soon as the motherboard is eliminated, you may proceed with the remainder of the disassembly course of.
Disconnecting the Drive
To disconnect the drive, you’ll require a T8 Torx screwdriver and a spudger or plastic opening device.
- Unplug the Xbox One from the facility outlet and different cables.
- Place the Xbox One the wrong way up on a flat floor.
- Find the 4 T8 Torx screws securing the underside panel and take away them.
- Gently pry open the underside panel utilizing a spudger or plastic opening device. Begin from the rear of the console close to the facility provide unit, and work your manner across the edges.
- Find the drive bay, which is an oblong metallic enclosure on the fitting facet of the console.
- Disconnect the 2 SATA cables from the drive. One is an information cable and the opposite is an influence cable. To do that, gently pull on the plastic tabs on every cable’s connector.
- Disconnect the 2 energy cables from the drive. They’re positioned on the entrance of the drive and are linked with plastic push-on connectors. Gently pull on the connectors to detach them.
- Take away the 4 T8 Torx screws securing the drive to the chassis.
- Rigorously elevate the drive out of the console.
| Part | Removing Methodology |
|---|---|
| Backside Panel | Take away 4 T8 Torx screws |
| SATA Information Cable | Pull on plastic tab on connector |
| SATA Energy Cable | Pull on plastic tab on connector |
| Energy Cables (2) | Pull on plastic push-on connectors |
| Drive Enclosure | Take away 4 T8 Torx screws |
Unhooking the SATA Connectors
Now that the optical drive is accessible, find the 2 SATA connectors linked to it. Use your fingers or a spudger to softly unhook each connectors. Watch out to not harm the connectors or the cable.
Eradicating the Screws
Subsequent, take away the 2 screws securing the optical drive to the console. These screws are normally positioned on the highest of the drive.
Sliding Out the Optical Drive
After the screws are eliminated, you may fastidiously slide the optical drive out of the console. Maintain it by the perimeters to keep away from touching the delicate elements on the entrance.
Disconnect the Energy Cable
Lastly, disconnect the facility cable from the optical drive by gently urgent on the discharge tab and pulling it out.
Here is a desk summarizing the steps for eradicating the optical drive:
| Step | Motion |
|---|---|
| 1 | Take away the highest panel |
| 2 | Open the optical drive tray |
| 3 | Unhook the SATA connectors |
| 4 | Take away the screws |
| 5 | Slide out the optical drive |
| 6 | Disconnect the facility cable |
Unplugging the Controller Ports
To unplug the controller ports, you may have to take away the back and front panels of the Xbox One. As soon as you have carried out that, you may see the controller ports on the motherboard. They’re held in place by a couple of screws, which you’ll take away with a Phillips head screwdriver. As soon as you have eliminated the screws, you may unplug the controller ports from the motherboard.
Here is a extra detailed information on how one can unplug the controller ports:
1. Flip off the Xbox One and unplug it from the facility outlet.
2. Take away the back and front panels of the Xbox One.
3. Find the controller ports on the motherboard.
4. Take away the screws that maintain the controller ports in place.
5. Unplug the controller ports from the motherboard.
6. Reattach the screws to the controller ports.
7. Reattach the back and front panels of the Xbox One.
8. Plug the Xbox One again into the facility outlet and switch it on.
| Step | Motion |
|---|---|
| 1 | Flip off the Xbox One and unplug it from the facility outlet. |
| 2 | Take away the back and front panels of the Xbox One. |
| 3 | Find the controller ports on the motherboard. |
| 4 | Take away the screws that maintain the controller ports in place. |
| 5 | Unplug the controller ports from the motherboard. |
| 6 | Reattach the screws to the controller ports. |
| 7 | Reattach the back and front panels of the Xbox One. |
| 8 | Plug the Xbox One again into the facility outlet and switch it on. |
Eradicating the Entrance Panel
The entrance panel of the Xbox One will be eliminated to entry the inner elements for upkeep or restore. Listed below are the steps to take away the entrance panel:
1. Energy Down and Unplug the Xbox One
Earlier than beginning, make sure that the Xbox One is powered down and unplugged from the facility outlet.
2. Take away the Screws
Find the 2 screws securing the entrance panel to the console physique on the underside edge. Take away these screws utilizing a T8 Torx screwdriver.
3. Raise the Entrance Panel
Gently elevate the entrance panel from the underside edge and pull it ahead to detach it from the console physique.
4. Disconnect the Ribbon Cable
Find the ribbon cable connecting the entrance panel to the console’s motherboard. Rigorously elevate the plastic tab securing the cable and disconnect it.
5. Take away the Speaker Grill
The speaker grill is positioned on the entrance panel. Use a plastic spudger or a skinny flathead screwdriver to pry off the grill.
6. Disconnect the Wire Harness
Find the wire harness connecting the facility and eject buttons to the motherboard. Rigorously disconnect the harness by lifting the plastic tab securing it.
7. Take away the Button Boards
The button boards for the facility and eject buttons are positioned behind the speaker grill. Use a plastic spudger to pry the boards free and take away them.
8. Take away the Backplate
The backplate of the entrance panel homes the IR receiver and LED lights. Take away the 2 screws on the backplate utilizing a T8 Torx screwdriver. The backplate can then be pulled off.
| Screw Dimension | Location |
|---|---|
| T8 Torx | Backside fringe of the entrance panel (2) |
| T8 Torx | Backplate of the entrance panel (2) |
Reassembling the Console
Now that you’ve got efficiently disassembled your Xbox One, it is time to reassemble it. Comply with these steps in reverse order to place your console again collectively.
9. Reattach the Energy Provide
To reattach the facility provide, first align the connector on the facility provide with the corresponding port on the motherboard. Make it possible for the connector is going through the proper manner; it should solely slot in one course. As soon as the connector is aligned, push down on the facility provide till it clicks into place. You need to hear a satisfying “click on” when the facility provide is securely connected.
Subsequent, change the screws that you simply eliminated earlier to carry the facility provide in place. Tighten the screws till they’re comfortable, however don’t overtighten them.
To reattach the facility provide, first align the connector on the facility provide with the corresponding port on the motherboard. Make it possible for the connector is going through the proper manner; it should solely slot in one course. As soon as the connector is aligned, push down on the facility provide till it clicks into place. You need to hear a satisfying “click on” when the facility provide is securely connected.
Subsequent, change the screws that you simply eliminated earlier to carry the facility provide in place. Tighten the screws till they’re comfortable, however don’t overtighten them.
| Screw Dimension | Amount |
|—|—|
| M3 x 4 mm | 4 |
Lastly, reconnect the facility cable to the again of the Xbox One and plug it again into an outlet.
Troubleshooting Ideas
For those who’re having bother taking your Xbox One aside, listed below are a couple of troubleshooting ideas:
1. Ensure you have the fitting instruments.
You may want a Phillips #0 screwdriver, a Torx T8 screwdriver, and a撬棒工具. If you do not have these instruments, yow will discover them at most {hardware} shops.
2. Comply with the directions fastidiously.
For those who’re undecided how one can do one thing, confer with the directions that got here along with your Xbox One or lookup a tutorial on-line.
3. Be affected person.
Taking aside your Xbox One is usually a time-consuming course of. Do not rush it, or you possibly can harm your console.
4. Use anti-static measures.
Once you’re working in your Xbox One, it is vital to take anti-static measures to forestall harm to the elements.
5. Preserve monitor of the screws.
There are numerous screws that maintain the Xbox One collectively. Ensure you maintain monitor of them so to put all the things again collectively correctly.
6. Take photos, if wanted.
For those who’re undecided how one can put one thing again collectively, take an image of it earlier than you disassemble it. This can assist you to keep in mind the way it goes collectively.
7. Do not power something.
If one thing does not wish to come aside, do not power it. You could possibly harm your Xbox One. Attempt utilizing a unique device or method.
8. For those who’re caught, get assist.
For those who’re actually caught, do not hesitate to get assist from a good friend, member of the family, or skilled restore technician.
9. For those who harm your Xbox One, do not panic.
For those who by accident harm your Xbox One whilst you’re taking it aside, do not panic. Generally, the harm will be repaired. Contact Microsoft Help for help.
10. Security first.
All the time comply with the protection directions that got here along with your Xbox One. Keep away from chopping your self on the sharp edges of the console, and watch out to not drop any small elements.
How To Take Xbox One Aside
To take Xbox One aside, you will want a couple of instruments, together with a Torx screwdriver, a Phillips screwdriver, and a spudger. After getting your instruments, comply with these steps:
- Energy down the Xbox One and unplug it from the facility outlet.
- Take away the screws from the again of the console utilizing the Torx screwdriver.
- Gently pry open the case utilizing the spudger.
- Disconnect the facility provide from the motherboard.
- Take away the screws from the motherboard utilizing the Phillips screwdriver.
- Gently elevate the motherboard out of the case.
- Disconnect the ribbon cables from the motherboard.
- Take away the screws from the optical drive utilizing the Torx screwdriver.
- Gently elevate the optical drive out of the case.
- Disconnect the facility provide from the optical drive.
- Take away the screws from the laborious drive utilizing the Torx screwdriver.
- Gently elevate the laborious drive out of the case.
- Disconnect the facility provide from the laborious drive.
- Reassemble the Xbox One in reverse order.
Individuals Additionally Ask About How To Take Xbox One Aside
How do I open an Xbox One controller?
To open an Xbox One controller, you will want a Torx screwdriver. After getting your screwdriver, comply with these steps:
- Take away the screws from the again of the controller.
- Gently pry open the case.
- Disconnect the battery.
- Take away the screws from the motherboard.
- Gently elevate the motherboard out of the case.
- Disconnect the ribbon cables from the motherboard.
- Reassemble the controller in reverse order.
How do I change the thermal paste on an Xbox One?
To exchange the thermal paste on an Xbox One, you will want a brand new tube of thermal paste, a spudger, and a Phillips screwdriver. After getting your supplies, comply with these steps:
- Energy down the Xbox One and unplug it from the facility outlet.
- Take away the screws from the again of the console utilizing the Torx screwdriver.
- Gently pry open the case utilizing the spudger.
- Disconnect the facility provide from the motherboard.
- Take away the screws from the motherboard utilizing the Phillips screwdriver.
- Gently elevate the motherboard out of the case.
- Take away the outdated thermal paste from the CPU and GPU utilizing the spudger.
- Apply a brand new layer of thermal paste to the CPU and GPU.
- Reassemble the Xbox One in reverse order.
