Changing a two-handle bathtub faucet is just not as tough as it could appear. With a number of easy instruments and slightly little bit of endurance, you may have your new faucet put in very quickly.
Step one is to show off the water provide to the tub. That is often finished by turning off the valves positioned underneath the sink. As soon as the water is turned off, you may take away the outdated faucet by unscrewing the nuts that maintain it in place. Watch out to not harm the plumbing when you find yourself doing this.
As soon as the outdated faucet is eliminated, you may set up the brand new one. Begin by inserting the brand new faucet within the gap within the bathtub. Then, screw on the nuts that maintain it in place. Make sure to tighten the nuts securely, however don’t overtighten them. Lastly, activate the water provide and examine for leaks. If there are any leaks, tighten the nuts till the leaks cease.
Collect Crucial Instruments and Supplies
Changing a two-handle bathtub faucet requires a number of important instruments and supplies to make sure a easy and profitable set up. This is a complete listing of what you may want:
Instruments
- Adjustable wrench or spanner
- Phillips head screwdriver
- Flat head screwdriver
- Plumbers putty or Teflon tape
- Bucket or bowl
- Rags or towels
Supplies
| Part | Amount |
|---|---|
| New two-handle bathtub faucet | 1 |
| Faucet handles | 2 |
| Faucet aerators (non-obligatory) | 2 |
| Pipe dope or thread sealant | As wanted |
Moreover, you might need to contemplate bringing a flashlight for higher visibility underneath the sink and a pair of labor gloves for defense.
Flip Off Water
Earlier than you start engaged on the tap, it is vital to show off the water provide. It will stop water from spraying out of the tap if you take away the handles and cartridge. To show off the water provide, find the shut-off valves underneath the sink. The valves will usually be positioned on the base of the tap, the place the water strains connect with the tap. Flip the valves clockwise to show off the water provide.
If there aren’t any shut-off valves underneath the sink, you will have to show off the water provide to the whole home. To do that, find the principle water shut-off valve, which is often positioned close to the entrance of the home, within the basement, or in a utility closet. Flip the valve clockwise to show off the water provide.
Suggestions for Turning Off the Water
Listed here are a number of suggestions for turning off the water provide:
- Just be sure you have a wrench or pliers readily available to show the shut-off valves.
- If the shut-off valves are tough to show, you may attempt utilizing a pair of pliers to get a greater grip.
- In case you are unable to show off the water provide, it’s best to name a plumber for help.
| Device | Function |
| Wrench or pliers | To show the shut-off valves |
Take away Aerators and Handles
Eradicating Aerators
Begin by unscrewing the aerator from the tap utilizing a wrench. If the aerator is caught, you should use a pair of pliers to softly loosen it.
As soon as the aerator is eliminated, it is possible for you to to see the cartridge. The cartridge is held in place by a screw, which you will have to take away utilizing a screwdriver.
As soon as the screw is eliminated, it is possible for you to to carry the cartridge out of the tap. Watch out to not lose the washer that’s positioned behind the cartridge.
Eradicating Handles
To take away the handles, you will have to find the set screws which are holding them in place. The set screws are often positioned on the underside of the handles.
After you have positioned the set screws, you will have to loosen them utilizing a screwdriver. Watch out to not over-tighten the set screws, as this could harm the handles.
As soon as the set screws are loosened, it is possible for you to to drag the handles off the tap.
| Device | Description |
|---|---|
| Wrench | Used to unscrew the aerator. |
| Screwdriver | Used to take away the cartridge screw and set screws. |
| Pliers | Used to loosen a caught aerator. |
| Washer | Situated behind the cartridge, it should not be misplaced. |
| Set screws | Maintain the handles in place. |
Disconnect Provide Strains
As soon as the handles and trim are eliminated, you will have to disconnect the availability strains. These are the versatile hoses that join the tap to the water provide pipes. Use an adjustable wrench to loosen the nuts that join the hoses to the tap.
Watch out to not overtighten the nuts, as you may harm the hoses. As soon as the nuts are unfastened, you may fastidiously pull the hoses off the tap.
If the hoses are outdated or broken, you might want to interchange them. To do that, minimize the outdated hoses off the tap and the availability pipes. Then, connect the brand new hoses to the tap and the availability pipes utilizing the nuts that got here with the brand new hoses.
As soon as the availability strains are disconnected, you may take away the outdated faucet from the sink or tub.
| Suggestions |
|---|
| In case you are having bother disconnecting the availability strains, you should use a pair of pliers that will help you loosen the nuts. |
| Watch out to not harm the availability strains when you find yourself disconnecting them. |
| In case you are changing the availability strains, guarantee that they’re the right size and that they’re rated for the water strain in your house. |
Take away Faucet Base
After eradicating the handles and cartridge, now you can take away the tap base. Place a bucket or towel underneath the tap to catch any water which will leak out.
Utilizing an adjustable wrench, loosen the nuts which are holding the tap base in place. Watch out to not overtighten the nuts, as this could harm the tap.
As soon as the nuts are unfastened, you may gently pull the tap base off of the bathtub deck.
If the tap base is caught, you might want to make use of a rubber mallet to softly faucet it unfastened. Watch out to not hit the tap too exhausting, as this could harm it.
As soon as the tap base is eliminated, now you can entry the plumbing connections.
Suggestions for Eradicating the Faucet Base
| Suggestions | Particulars |
|---|---|
| Use a bucket or towel to catch any water which will leak out | It will assist to stop water from damaging your ground or carpet. |
| Watch out to not overtighten the nuts | Overtightening the nuts can harm the tap. |
| If the tap base is caught, use a rubber mallet to softly faucet it unfastened | Watch out to not hit the tap too exhausting, as this could harm it. |
Clear Mounting Floor
Earlier than you start putting in the brand new faucet, it is vital to completely clear the mounting floor. It will assist to make sure that the brand new faucet is put in securely and that there aren’t any leaks. Listed here are the steps to scrub the mounting floor:
-
Take away any outdated caulk or sealant from across the outdated faucet. You should use a utility knife or a razor blade to fastidiously scrape away the caulk.
-
Clear the floor with a degreaser. It will assist to take away any dust, grime, or oil that would stop the brand new faucet from bonding correctly.
-
Rinse the floor with clear water and permit it to dry utterly.
| Tip | Description |
|---|---|
| Use a scrub brush to scrub the floor completely. | It will assist to take away any cussed dust or grime. |
| Enable the floor to dry utterly earlier than putting in the brand new faucet. | It will assist to make sure that the brand new faucet is put in securely. |
Apply Plumber’s Putty and Set up Base
Step 7: Apply Plumber’s Putty and Set up Base
7.1: Take away the outdated plumber’s putty from the bottom of the brand new faucet utilizing a putty knife or scraper. Clear the world completely with rubbing alcohol and permit it to dry.
7.2: Roll out a rope of plumber’s putty about 1/4 inch thick and 6 inches lengthy. Place the putty across the base of the tap, leaving a small gap within the middle for the water provide strains.
7.3: Flip the tap the other way up and place it over the mounting holes within the bathtub. Be sure the putty is evenly distributed across the base and filling any gaps.
7.4: Place the mounting bolts via the holes within the faucet and into the tub. Tighten the nuts by hand till comfortable.
7.5: Flip the tap right-side up and manually tighten the mounting nuts additional. Keep away from overtightening, as this could harm the tap or bathtub.
7.6: Use a stage to make sure the tap is stage. Regulate the mounting nuts as mandatory.
Set up Handles
1. Place the handles on the stems.
2. Apply a small quantity of plumbers grease to the threads of the deal with screws.
3. Insert the deal with screws into the handles and tighten them till they’re comfortable.
4. Use a wrench to tighten the packing nuts on every deal with.
5. Activate the water and examine for leaks. If there’s a leak, tighten the packing nuts till the leak stops.
6. Set up the aerators on every deal with.
7. Activate the water and examine for leaks. If there’s a leak, tighten the aerators till the leak stops.
8. Verify the operation of the tap. The handles ought to flip easily and the water ought to movement evenly from the aerators. If the tap doesn’t function correctly, examine the next:
| Attainable Downside | Answer |
|---|---|
| The handles are stiff | Loosen the packing nuts on the handles |
| The water doesn’t movement evenly from the aerators | Clear the aerators |
| The tap is leaking | Tighten the packing nuts on the handles or aerators |
Join Provide Strains
9. **Join Provide Strains to Faucet:**
a. Wrap plumber’s tape clockwise across the threaded finish of the cold and hot provide strains. Tighten them by hand onto the corresponding faucet inlets marked “H” and “C.”
b. **Use a Basin Wrench to Safe:**
| Tip | Profit |
|---|---|
| Insert a basin wrench into the opening within the faucet physique. | Permits entry to the nuts beneath the tap. |
| Tighten the nuts till they’re comfortable, however keep away from overtightening. | Prevents leaks and ensures a safe connection. |
c. **Verify Connections:**
Activate the water provide and examine for leaks on the faucet inlets and provide line connections. If any leaks happen, tighten the connections additional as wanted.
Flip On Water and Verify for Leaks
As soon as the outdated faucet is eliminated, it is essential to activate the water provide to check for any potential leaks earlier than putting in the brand new one. Observe these steps to make sure a watertight seal:
- Open each the cold and hot water valves positioned beneath the sink.
- Run each handles to permit water to movement via the pipes.
- Examine the bottom of the tap, the availability strains, and some other connections for any indicators of water leakage.
- If you happen to encounter any leaks, tighten the connections additional utilizing a wrench or pliers.
- As soon as the leaks have been addressed, flip off each water valves once more.
- Proceed with the set up of the brand new faucet, taking additional care to safe all connections.
- As soon as the brand new faucet is totally put in, activate the water valves once more and examine for any remaining leaks.
- If all connections are safe and there aren’t any leaks, proceed to the following step of testing the performance of the tap.
- If you happen to encounter any persistent leaks that can’t be resolved, seek the advice of a licensed plumber for skilled help.
| Troubleshooting Leaks | |
|---|---|
| Leak at faucet base | Tighten the locknut beneath the tap. |
| Leak at provide line connections | Use a wrench to tighten the nuts connecting the availability strains to the tap. |
| Leak at pop-up drain | Verify the drain stopper meeting and exchange any worn-out elements. |
How To Substitute A Two Deal with Bathtub Faucet
Changing a two-handle bathtub faucet is a comparatively easy activity that may be accomplished in a number of hours. With the appropriate instruments and supplies, it can save you your self the price of hiring a plumber.
Instruments and Supplies
• Adjustable wrench
• Basin wrench
• Plumber’s putty
• Teflon tape
• New bathtub faucet
• Utility knife
Directions
- Flip off the water provide to the tub. There needs to be two shut-off valves positioned underneath the sink. Flip the handles clockwise to shut them.
- Open the tub faucet to launch any remaining water strain.
- Use the adjustable wrench to loosen the nuts that maintain the handles in place. Take away the handles.
- Use the basin wrench to loosen the nuts that maintain the tap physique in place. Take away the tap physique.
- Apply a bead of plumber’s putty to the bottom of the brand new faucet physique. Wrap the threads of the tap physique with Teflon tape.
- Set up the brand new faucet physique and tighten the nuts with the basin wrench.
- Set up the handles and tighten the nuts with the adjustable wrench.
- Activate the water provide to the tub and examine for leaks. If there are any leaks, tighten the nuts additional.
Folks Additionally Ask About How To Substitute A Two Deal with Bathtub Faucet
How a lot does it value to interchange a bath faucet?
The fee to interchange a bath faucet can range relying on the kind of faucet you select and the complexity of the set up. Nonetheless, you may count on to pay between $100 and $500 for the tap and set up.
Can I exchange a bath faucet myself?
Sure, you may exchange a bath faucet your self with the appropriate instruments and supplies. Nonetheless, if you’re not comfy working with plumbing, it’s best to rent a plumber.
What’s the finest kind of bath faucet to purchase?
One of the best kind of bath faucet for you’ll rely in your wants and preferences. Some common sorts of bathtub taps embody:
- Two-handle taps
- Single-handle taps
- Thermostatic taps
- Sensor taps
