Changing a belt on a Maytag washer W10873035 is a comparatively easy process that may be accomplished in about an hour. An important factor is to just be sure you have the appropriate belt on your mannequin of washer. You’ll find the right belt by trying up the mannequin variety of your washer within the Maytag elements catalog. After you have the right belt, you’ll be able to comply with the steps under to put in it.
First, you’ll need to unplug the washer from the ability outlet and switch off the water provide. Subsequent, you’ll need to take away the again panel of the washer. To do that, find the screws which might be holding the again panel in place and take away them. As soon as the screws are eliminated, you need to be capable of pull the again panel off of the washer. Now, you’ll need to find the belt. The belt is an extended, black rubber band that’s wrapped across the motor pulley and the transmission pulley. To take away the belt, merely slip it off of the pulleys. Lastly, you’ll need to put in the brand new belt. To do that, merely slip the brand new belt over the motor pulley and the transmission pulley. As soon as the brand new belt is in place, you’ll be able to reattach the again panel of the washer. Be sure that the belt is tight earlier than you reattach the again panel. To do that, merely flip the motor pulley by hand. The belt must be tight sufficient in order that it doesn’t slip off of the pulleys, however not so tight that it’s troublesome to show the motor pulley.
As soon as the again panel is reattached, you’ll be able to plug the washer again into the ability outlet and activate the water provide. Your washer ought to now be working correctly.
Eradicating the Washer’s Entrance Panel
To provoke the dismantling course of, meticulously unplug the washer’s energy wire from {the electrical} outlet. This significant security measure prevents any potential electrical hazards. Find the 2 screws securing the management panel to the highest of the washer’s entrance panel. Utilizing a Phillips head screwdriver, fastidiously take away these screws, being conscious to not injury the panel or surrounding elements.
Proceed to the underside of the entrance panel, the place you’ll encounter two further screws hidden behind the kickplate. These screws require a 1/4-inch hex head driver to extract. As soon as eliminated, gently pull the kickplate straight in the direction of you to detach it from the washer.
With the kickplate out of the way in which, now you can deal with eradicating the entrance panel. Firmly grasp the panel on either side and pull it in the direction of you with regular drive. The panel shall be held in place by a collection of plastic clips, which can launch with a delicate tug. As soon as the clips are indifferent, slowly carry the panel upwards and out of the washer.
Warning: Deal with the entrance panel with utmost care because it comprises delicate electrical elements. Keep away from bending or twisting the panel to stop injury.
| Instruments Required |
|---|
| Phillips Head Screwdriver |
| 1/4-Inch Hex Head Driver |
Detaching the Drive Belt
The drive belt is an important element that powers the washer’s drum motion. To entry and detach it, comply with these steps:
Eradicating the Washer Prime
1. Unplug the washer and disconnect the water hoses.
2. Find the 2 screws behind the washer, close to the highest. Take away them utilizing a screwdriver.
3. Fastidiously carry and take away the washer prime, setting it apart.
Accessing the Drive Belt
4. Find the drive belt pulley, which is normally connected to the motor on the backside of the washer.
5. Utilizing a pair of pliers or a spanner, gently pry the belt off the pulley.
6. As soon as the belt is indifferent, take away it from the washer.
Ideas for Detaching the Belt
- Be cautious when prying the belt off the pulley, as it might be below pressure.
- If the belt is caught, use a small quantity of penetrating oil to loosen it.
- Observe the belt’s orientation for correct reinstallation.
| Part | Elimination Course of |
|---|---|
| Washer Prime | Unplug, take away water hoses, unscrew and carry off |
| Drive Belt | Pry off pulley utilizing pliers or spanner |
| Belt Pressure | Use penetrating oil if caught |
| Belt Orientation | Observe place for reinstallation |
Putting in the New Drive Belt
4. Putting in the New Drive Belt
a) Place the brand new drive belt across the motor pulley, guaranteeing that it’s seated appropriately within the groove.
b) Route the belt across the loafer pulley and tensioner pulley, following the right routing diagram as per your washer mannequin.
c) Place the belt across the transmission pulley, ensuring to align it with the groove and information pins.
d) Manually rotate the transmission pulley clockwise till the belt is tight. Verify the strain by making use of gentle strain to the belt; it ought to deflect about 1/2 to 1 inch when pressed.
e) Tighten the tensioner pulley bolt or nut to safe the belt in place. Don’t overtighten, as this may injury the belt or pulley.
f) Reconnect {the electrical} connectors to the transmission and motor.
g) Exchange the again panel of the washer and safe it with screws.
Reattaching the Washer’s Entrance Panel
As soon as the brand new belt has been put in, it is time to reattach the washer’s entrance panel. This is how:
1. Align the Panel
Fastidiously align the entrance panel with the washer’s body, guaranteeing that the sides are flush and the panel is degree.
2. Insert Prime Tabs
Find the 2 tabs on the prime of the entrance panel and punctiliously insert them into the slots on the washer’s body.
3. Push Down
Gently push down on the highest of the entrance panel till you hear a click on, indicating that the tabs have snapped into place.
4. Insert Backside Clips
Find the 2 clips on the backside of the entrance panel and slide them into the slots on the washer’s body.
5. Safe Screws
Use a screwdriver to tighten the screws that safe the entrance panel to the body, guaranteeing that they’re comfortable however not overtightened.
6. Set up Kick Plate
The kick plate is an ornamental panel that covers the underside of the washer. To put in it, comply with these steps:
| Step | Directions |
|---|---|
| a) | Place the kick plate on the backside of the entrance panel. |
| b) | Insert the tabs on the kick plate into the slots on the entrance panel. |
| c) | Push down on the kick plate till it snaps into place. |
| d) | Use a screwdriver to tighten the screws that safe the kick plate to the entrance panel. |
Verifying Correct Belt Set up
After changing the belt, it is essential to confirm its correct set up. Observe these steps:
- Right Belt Path: Make sure the belt follows the right path across the motor pulley, loafer pulley (if current), and transmission pulley.
- No Slack: The belt must be taut with no slack between the pulleys. A unfastened belt can slip and compromise efficiency.
- No Interference: Confirm that the belt doesn’t intrude or rub in opposition to another elements, resembling wires, hoses, or the washer cupboard.
- Balanced Pressure: The belt ought to have equal pressure on either side. Use a belt pressure gauge or your fingers to test for any imbalances.
- Clean Rotation: With the ability off, manually rotate the motor pulley to test for any binding or extreme resistance. The pulleys ought to spin easily with a delicate push.
- Listening for Noises: Run a take a look at cycle to hear for any irregular noises coming from the belt space. A squealing or grinding sound might point out misalignment or a broken belt.
- Efficiency Verify: If the belt seems to be put in appropriately, run a full wash cycle to test for correct performance. The washer ought to agitate, spin, and drain usually with none belt-related points.
Supplies You will Want
Earlier than beginning, collect the next supplies:
– New drive belt (half quantity W10873035)
– Socket wrench or pliers
– Screwdriver
– Flashlight (non-compulsory)
Security Precautions
Unplug the washer from the ability outlet earlier than starting any repairs.
Put on gloves and security glasses to guard your self from sharp edges and particles.
Step-by-Step Directions
1.
Take away the Prime Panel
Find the 2 screws holding the highest panel in place. Take away the screws and carry the highest panel off the washer.
2.
Find the Drive Belt
The drive belt is situated across the motor pulley and the transmission pulley on the backside of the washer.
3.
Take away the Outdated Belt
Use a socket wrench or pliers to loosen the strain on the belt. Slip the belt off the pulleys and take away it from the washer.
4.
Set up the New Belt
Place the brand new belt across the motor pulley first. Then, stretch the belt over the transmission pulley and alter the strain utilizing the socket wrench or pliers.
5.
Exchange the Prime Panel
Align the highest panel with the washer and press it down till it clicks into place.
6.
Reconnect the Energy
Plug the washer again into the ability outlet.
7.
Check the Washer
Run the washer by a brief cycle to make sure that the brand new belt is working correctly.
Frequent Troubleshooting Ideas
The belt retains coming off
1. Verify the strain on the belt. It must be tight sufficient to remain on the pulleys, however not so tight that it places pressure on the motor.
2. Make sure the belt is routed appropriately across the pulleys.
3. Examine the pulleys for injury. If they’re worn or broken, they could have to be changed.
4. Verify for different objects which may be caught within the belt, resembling unfastened clothes or particles.
5. Exchange the belt with a brand new one whether it is broken or stretched.
6. Verify the motor bearings. If they’re worn or broken, they could trigger the motor pulley to wobble, which might trigger the belt to return off.
7. Examine the transmission. Whether it is broken or worn, it might not be capable of flip the bathtub correctly, which might trigger the belt to return off.
8. Verify the motor capacitor. If it’s not working correctly, it might probably trigger the motor to run erratically, which might result in the belt coming off. The motor capacitor is a cylindrical element that’s related to the motor. It’s normally black or brown in shade. To check the capacitor, you’ll need a multimeter. Disconnect the ability to the washer earlier than testing the capacitor. Set the multimeter to the capacitance setting and contact the probes to the terminals on the capacitor.
Security Precautions for Washer Belt Set up
1. Unplug the washer or disconnect it from the ability provide earlier than beginning any work.
2. Put on protecting gloves and security glasses to keep away from accidents from sharp edges or chemical substances.
3. Make sure the washer is secure and degree earlier than making an attempt to put in the belt.
4. Clear the world across the washer of any obstacles or particles.
5. Have a helper help you with lifting the equipment if needed.
6. Make sure that the washer is in its off cycle and the lid is open.
7. Take away the again or entrance panel of the washer, relying on the mannequin.
8. Find the previous belt and punctiliously detach it from the pulleys.
9. Examine the Belt for Harm
Examine the previous belt for any indicators of injury, together with cracks, cuts, fraying, or extreme put on. If any injury is discovered, change the previous belt with a brand new one to make sure optimum efficiency.
To totally examine the belt, use a magnifying glass to look at its floor for positive cracks or tears. Pay explicit consideration to the areas the place the belt bends and makes contact with the pulleys.
Really feel the belt’s texture to detect any tough spots, thinning, or areas the place the rubber has hardened or turn out to be brittle. These indications might sign potential breakage or slippage throughout operation.
Further Ideas and Issues
Unplug the washer earlier than beginning.
It is a essential security precaution to stop any electrical shocks whereas engaged on the washer.
Collect the mandatory instruments.
You have to a screwdriver, a wrench, and a brand new belt.
Find the belt.
The belt is normally situated across the motor pulley and the transmission pulley.
Take away the previous belt.
Use the wrench to loosen the strain on the belt after which slip it off the pulleys.
Set up the brand new belt.
Slip the brand new belt onto the motor pulley first after which onto the transmission pulley. Make sure that the belt is correctly aligned and seated within the grooves.
Tighten the belt.
Use the wrench to tighten the strain on the belt. The belt must be tight sufficient to stop slipping however not so tight that it places pointless pressure on the motor or the transmission.
Reassemble the washer.
Put the entrance panel again on and fasten the screws.
Check the washer.
Plug the washer again in and run it by a brief cycle to verify it’s working correctly.
10. Belt Pressure Adjustment
Correct belt pressure is essential for optimum washer efficiency. If the belt is simply too unfastened, it might slip and trigger the washer to vibrate or make noise. If the belt is simply too tight, it might put pointless pressure on the motor and the transmission, resulting in untimely failure.
To regulate the belt pressure, comply with these steps:
| Step | Description |
|---|---|
| 1 | Loosen the 2 bolts that maintain the motor mount in place. |
| 2 | Transfer the motor ahead or backward to regulate the belt pressure. |
| 3 | Tighten the bolts to safe the motor mount in place. |
| 4 | Run the washer by a brief cycle to test the belt pressure. |
Repeat these steps till the belt pressure is appropriate.
How To Set up Belt On Maytag Washer W10873035
Changing the belt on a Maytag washer mannequin W10873035 is a comparatively easy restore that may be accomplished in about an hour. An important factor is to just be sure you have the right belt on your mannequin and that you just comply with the directions fastidiously.
Supplies:
- New belt
- Screwdriver
- Bucket
Directions:
- Unplug the washer from the ability outlet.
- Flip off the water provide to the washer.
- Disconnect the drain hose from the standpipe.
- Tilt the washer again barely and place a bucket below the underside entrance of the washer to catch any water that will leak out.
- Take away the 2 screws that maintain the entrance panel in place.
- Pull the entrance panel ahead and off the washer.
- Find the belt across the motor pulley and the transmission pulley.
- Loosen the loafer pulley with a screwdriver.
- Take away the previous belt from the pulleys.
- Place the brand new belt across the motor pulley and the transmission pulley.
- Tighten the loafer pulley.
- Exchange the entrance panel.
- Reconnect the drain hose to the standpipe.
- Activate the water provide to the washer.
- Plug the washer into the ability outlet.
- Run the washer by a take a look at cycle.
Folks Additionally Ask About How To Set up Belt On Maytag Washer W10873035
Can I change the belt on my Maytag washer myself?
Sure, changing the belt on a Maytag washer is a comparatively easy restore that may be accomplished in about an hour. Nevertheless, you will need to just be sure you have the right belt on your mannequin and that you just comply with the directions fastidiously.
How do I do know if the belt on my Maytag washer is damaged?
There are a number of indicators that will point out that the belt in your Maytag washer is damaged. These embody:
- The washer won’t agitate or spin.
- The washer makes a squealing or thumping noise.
- The washer leaks water.
How a lot does it value to exchange the belt on a Maytag washer?
The fee to exchange the belt on a Maytag washer will range relying on the mannequin of the washer and the price of the belt. Nevertheless, you’ll be able to anticipate to pay between $50 and $100 for the restore.
