Putting in jigsaw blades on DeWalt 20-volt jigsaws is usually a breeze! Here is a step-by-step information that can assist you get it finished rapidly and effectively. Start by making certain that your jigsaw is off and the battery is disconnected. It is essential to work on a cooled-down jigsaw to forestall any burns.
Find the blade ejection lever on the entrance of the noticed. It’s sometimes a small, spring-loaded lever. Push the lever away from you and concurrently pull down the blade clamp. This may can help you clear the trail for the brand new blade. Subsequent, align the brand new blade’s tooth going through downwards and insert it into the blade clamp. Fastidiously push the blade up till it’s securely held in place. Launch the blade clamp by pushing it in direction of you and lock the blade in place by partaking the blade ejection lever again into its unique place. Make sure the blade is firmly seated by gently pulling on it.
Lastly, reconnect the battery and activate the jigsaw. Check the blade by making a number of cuts on a scrap piece of wooden. If the blade cuts easily with none wobbling or vibration, you’ve gotten efficiently put in the blade. Bear in mind, it is indispensable to put on gloves and security glasses all through the method to your safety.
Disassembling the Jigsaw
Earlier than you may insert a brand new blade into your DeWalt 20V jigsaw, you could first disassemble the device. Observe these steps to take action safely and effectively:
1. Unplug the Jigsaw
At the start, it’s essential to unplug the jigsaw from the ability supply. This security precaution prevents unintended activation whereas disassembling the device. Find the ability twine and disconnect it on the plug.
As soon as the jigsaw is unplugged, you may proceed to the following steps.
2. Take away the Shoe Insert
The shoe insert is a small, detachable piece situated on the bottom of the jigsaw. To take away it, merely grasp the insert along with your fingers or a pair of pliers and pull it straight out. This may expose the blade clamp mechanism under.
3. Open the Blade Clamp
With the shoe insert eliminated, you will notice a steel blade clamp. To open the clamp, find the lever or knob on the facet of the jigsaw and rotate it counterclockwise. This may loosen the clamp and can help you insert or take away the jigsaw blade safely.
4. Take away the Previous Blade
As soon as the blade clamp is open, you may take away the previous blade. Grip the blade firmly with one hand and gently pull it straight up out of the clamp. If the blade is caught, it’s possible you’ll want to make use of a pair of pliers or a screwdriver to assist pry it free.
Inserting the New Blade
As soon as you’ve got chosen the suitable blade to your venture, it is time to insert it into the jigsaw. Here is an in depth step-by-step information:
Step 1: Take away the Base Plate
Loosen the screws holding the bottom plate in place utilizing an Allen key or wrench. Fastidiously elevate off the bottom plate to show the blade clamp.
Step 2: Open the Blade Clamp
Find the lever or dial that releases the blade clamp. Press or flip the discharge mechanism to open the clamp and permit the insertion of the brand new blade.
Step 3: Insert the Blade
Align the tooth of the brand new blade with the information slots on the blade clamp. Insert the blade into the clamp making certain that the tooth are going through within the right path. The blade needs to be inserted with the tooth pointing downward for slicing on the upstroke and upward for slicing on the downstroke.
| Slicing Course | Enamel Orientation |
|---|---|
| Upstroke (Slicing on the way in which up) | Enamel going through downward |
| Downstroke (Slicing on the way in which down) | Enamel going through upward |
Tip: In case you’re not sure of the proper tooth orientation, seek the advice of your jigsaw’s guide or verify the producer’s web site for particular steerage.
Step 4: Shut the Blade Clamp
As soon as the blade is inserted, press or flip the discharge mechanism once more to shut the blade clamp. Be certain that the blade is securely held in place with none wobble.
Step 5: Reattach the Base Plate
Place the bottom plate again onto the jigsaw and tighten the screws to safe it. Your new jigsaw blade is now put in and prepared to be used.
Securing the Blade
4. Tightening the Blade: A Complete Information
As soon as the blade is seated appropriately, it is essential to tighten it securely. Use the supplied wrench or key to carry the retaining bolt nonetheless whilst you flip the nut clockwise utilizing the opposite hand. Guarantee you’ve gotten a agency grip and apply sufficient pressure to snugly fasten the blade, however keep away from overtightening as it could warp or harm the blade. To make sure correct tightness, use a torque wrench set to the producer’s beneficial torque specification. Nonetheless, when you’re working with out a torque wrench, intention for a comfortable match that permits the blade to maneuver freely with out extreme play.
| Tip | Rationalization |
|---|---|
| Safe the blade firmly, however do not overtighten | Overtightening can warp or harm the blade |
| Use a torque wrench for exact tightening | Ensures correct tightness with out damaging the blade |
| Intention for a comfortable match with out extreme play | Permits the blade to maneuver freely throughout slicing |
Adjusting Blade Rigidity
As soon as you’ve got inserted the blade, you will want to regulate the blade stress to make sure it is held securely. Most DeWalt jigsaws have a tool-less blade stress lever or knob that lets you simply regulate the strain with out the necessity for a hex key or different instruments. Here is how one can regulate the blade stress:
- Establish the blade stress adjustment lever or knob in your particular DeWalt jigsaw mannequin.
- Maintain the lever or knob and switch it counterclockwise to loosen the blade stress.
- Insert the blade into the jigsaw and tighten the lever or knob clockwise till the blade is held firmly in place.
- Check the blade stress by gently pulling on the blade. It ought to really feel comfortable however not overly tight.
- If the blade strikes too simply or rattles, tighten the strain lever or knob additional. If the blade is simply too tight, it could bind or break throughout operation, so loosen the strain barely.
Ideas for Adjusting Blade Rigidity
- Totally different blades might require totally different stress settings. Thinner blades typically require much less stress than thicker blades.
- At all times verify the blade stress earlier than every use to make sure it is safe and correctly adjusted.
- Keep away from overtightening the blade stress, as this may harm the blade or the jigsaw mechanism.
Security Precautions
1. Put on Security Gear: At all times put on eye safety, gloves, and a mud masks when working with energy instruments.
2. Unplug Energy Instrument: Earlier than performing any upkeep or changes, be sure that the jigsaw is unplugged from the ability supply.
3. Examine Blade: Verify the blade for any harm or put on earlier than set up. Don’t use a broken blade.
4. Preserve Away from Blade: Preserve your fingers and fingers away from the blade space whereas the jigsaw is working.
5. Securely Clamp Workpiece: Safe the workpiece firmly earlier than beginning to lower. This may stop the fabric from transferring through the slicing course of.
6. Keep away from Kickbacks: Preserve a agency grip on the jigsaw and use each fingers to manage the device. Keep away from slicing into supplies which might be too thick or laborious, as this may trigger kickbacks.
7. Use Appropriate Blade: Select the proper blade for the fabric you’re slicing. Incorrect blade choice can result in ineffective slicing and potential hazards.
8. Observe Producers’ Directions: Consult with the producer’s directions for particular security tips and upkeep procedures.
9. Extra Precautions for 20 Volt DeWalt Jigsaws:
- Take away Battery Earlier than Altering Blade: At all times take away the battery from the jigsaw earlier than altering the blade.
- Find Blade Clamp Lever: Establish the blade clamp lever on the jigsaw, often situated close to the blade housing.
- Pull Up Clamp Lever: Pull up the blade clamp lever to launch the blade.
- Take away Previous Blade: Grip the previous blade firmly with gloved fingers and pull it straight out of the blade holder.
- Insert New Blade: Align the brand new blade with the blade holder and insert it securely.
- Safe Blade: Push down on the blade clamp lever to safe the brand new blade in place.
- Examine Blade Set up: Be certain that the blade is correctly put in and securely fixed earlier than persevering with.
Putting in Dewalt Jigsaw Blades 20 Volt
Step 1: Collect Supplies
You will want a Dewalt jigsaw, a Dewalt 20V jigsaw blade, and a Phillips head screwdriver.
Step 2: Put together the Jigsaw
Take away the battery from the jigsaw and insert the jigsaw blade into the blade clamp.
Step 3: Tighten the Blade Clamp
Use the Phillips head screwdriver to tighten the blade clamp screw till the blade is securely held.
Step 4: Reattach the Battery
Reattach the battery to the jigsaw.
Step 5: Check the Blade
Activate the jigsaw and make a number of check cuts to make sure the blade is put in appropriately and slicing easily.
Troubleshooting Ideas
1. The blade is just not slicing straight
Verify if the blade is put in appropriately and if the blade clamp is tight. If the issue persists, strive a brand new blade.
2. The blade is vibrating excessively
Verify if the blade is bent or broken. Whether it is, substitute the blade. Additionally, verify if the jigsaw is balanced correctly and if the blade clamp is tight.
3. The blade is just not slicing via the fabric
Verify if the blade is sharp and if the jigsaw is ready to the proper velocity for the fabric being lower. If the issue persists, strive a special blade.
4. The jigsaw is overheating
Cease utilizing the jigsaw and let it settle down. Verify if the blade is caught or if the jigsaw is clogged with sawdust. Clear the jigsaw and take a look at utilizing a brand new blade.
5. The jigsaw is making unusual noises
Cease utilizing the jigsaw and verify if there are any free components or broken elements. In case you discover any issues, contact a professional restore technician.
6. The jigsaw is just not beginning
Verify if the battery is charged and if the jigsaw is correctly plugged into an outlet. If the issue persists, strive a special battery or contact a professional restore technician.
7. The jigsaw is just not responding to the set off
Verify if the set off is caught or broken. Whether it is, contact a professional restore technician.
8. The jigsaw is smoking
Cease utilizing the jigsaw instantly and unplug it from the outlet. Contact a professional restore technician.
9. The jigsaw is leaking oil
Cease utilizing the jigsaw and phone a professional restore technician.
10. The jigsaw is just not lined by the guarantee
If the jigsaw is just not lined by the guarantee, you may contact a professional restore technician. They will diagnose the issue and supply a value estimate for the repairs.
How To Set up Dewalt Jigsaw Blades 20 Volt
Putting in Dewalt jigsaw blades on a 20-volt jigsaw is an easy course of that may be accomplished in a couple of minutes. Listed below are the steps it’s good to observe:
- Flip off the jigsaw and unplug it from the ability supply. That is vital for security causes.
- Open the blade clamp. To do that, push the lever or button that’s situated on the facet of the jigsaw. The blade clamp will open, permitting you to take away the previous blade.
- Take away the previous blade. Grip the previous blade along with your fingers and pull it straight out of the blade clamp.
- Insert the brand new blade. Align the brand new blade with the blade clamp and insert it into the clamp. Make it possible for the tooth of the blade are going through within the right path.
- Shut the blade clamp. Push the lever or button that you simply used to open the blade clamp. The blade clamp will shut, securing the brand new blade in place.
- Plug within the jigsaw and switch it on. Your jigsaw is now prepared to make use of.
Individuals Additionally Ask About How To Set up Dewalt Jigsaw Blades 20 Volt
What’s one of the simplest ways to chop a straight line with a jigsaw?
To chop a straight line with a jigsaw, use a straight edge as a information. Place the straight edge alongside the road you need to lower and maintain it firmly in place. Then, begin slicing alongside the road, retaining the jigsaw in opposition to the straight edge.
What’s one of the simplest ways to chop a curve with a jigsaw?
To chop a curve with a jigsaw, use a freehand method. Begin by slicing alongside the skin fringe of the curve. Then, steadily transfer the jigsaw in direction of the within fringe of the curve, ensuring to maintain the blade perpendicular to the floor of the fabric.
What’s one of the simplest ways to chop a gap with a jigsaw?
To chop a gap with a jigsaw, first drill a pilot gap within the middle of the outlet. Then, insert the jigsaw blade into the pilot gap and begin slicing. Preserve the jigsaw perpendicular to the floor of the fabric and steadily transfer the jigsaw across the circumference of the outlet.
