Are you in search of to take away your Ring Doorbell Professional to exchange it with a brand new one, relocate it to a distinct spot, or for another motive? Eradicating a Ring Doorbell Professional is a comparatively easy course of that may be accomplished in just a few steps. Whether or not you are an skilled DIY fanatic or a first-timer, this information will give you clear directions and useful suggestions to make sure a profitable elimination. After getting eliminated your Ring Doorbell Professional, you’ll be able to proceed with the required actions, comparable to putting in a brand new doorbell or storing it for future use.
Earlier than you start the elimination course of, it’s essential to assemble the required instruments. You’ll need a Philips head screwdriver, a small flathead screwdriver, and a pair of needle-nose pliers. Moreover, in case your Ring Doorbell Professional is at the moment powered by batteries, you’ll need to take away them. After getting all the required instruments and supplies, you’ll be able to proceed with the next steps: 1. Take away the faceplate by inserting the small flathead screwdriver into the notch on the backside of the faceplate and gently prying it off. 2. Use the Philips head screwdriver to take away the 2 screws that safe the mounting bracket to the wall.
3. Fastidiously pull the Ring Doorbell Professional straight in the direction of you, disconnecting it from the mounting bracket. 4. In case your Ring Doorbell Professional is wired, disconnect the wires from the terminals on the again of the gadget. 5. Take away the mounting bracket from the wall by unscrewing the 2 screws that safe it. After getting accomplished these steps, your Ring Doorbell Professional might be efficiently faraway from the wall. Now you can proceed with the following steps, comparable to putting in a brand new doorbell or storing the Ring Doorbell Professional for future use. Keep in mind to deal with the gadget with care all through the elimination course of to keep away from any harm.
Safely Disconnect the Energy
Earlier than you start:
It is essential to take correct precautions earlier than disconnecting the ability to your Ring Doorbell Professional. Comply with these security tricks to keep away from any potential hazards:
- Determine the principle energy supply: Decide whether or not your Doorbell Professional is powered by batteries or a wired connection. If it is wired, you may have to find the circuit breaker or fuse field that provides energy to the doorbell.
- Flip off energy on the most important breaker: As soon as you have recognized the ability supply, flip off the ability to the circuit that feeds your doorbell. It will guarantee there is not any electrical present flowing by way of the gadget whenever you disconnect it.
- Double-check for energy: Use a multimeter or voltage tester to verify that the ability to the doorbell has been efficiently disconnected. This offers you peace of thoughts and stop any electrical accidents.
Extra Precautions:
| Situation | Precautions |
|---|---|
| Battery-powered Doorbell Professional | Take away the batteries from the gadget earlier than disconnecting it. |
| Wired Doorbell Professional | Flip off the ability on the circuit breaker or fuse field and disconnect the doorbell’s wires from {the electrical} junction field. |
| Shared Energy Supply | In case your Doorbell Professional shares an influence supply with different gadgets, disconnect all related gadgets earlier than turning off the ability. |
Keep in mind, security ought to all the time be your high precedence when working with electrical gadgets. By following these precautions, you’ll be able to guarantee a protected and profitable elimination of your Ring Doorbell Professional.
Take away the Faceplate
To take away the faceplate out of your Ring Doorbell Professional, observe these steps:
- Take away the screw. Use a Phillips screwdriver to take away the only screw situated within the backside heart of the faceplate.
- Pry the faceplate off. Fastidiously pry the faceplate off the doorbell base utilizing a plastic pry instrument or a flat-head screwdriver. Keep away from utilizing extreme drive, as it’s possible you’ll harm the gadget or surrounding surfaces.
- Disconnect the doorbell wire (non-compulsory). For those who’re planning to maneuver your doorbell to a brand new location, you may have to disconnect the doorbell wire. To do that, merely push down on the wire connector tab and pull the wire out.
Extra Suggestions for Eradicating the Faceplate Safely
Listed here are some extra suggestions for eradicating the faceplate of your Ring Doorbell Professional safely and effectively:
- Guarantee that you’ve the proper instruments for the job, comparable to a Phillips screwdriver and a plastic pry instrument or flat-head screwdriver.
- Apply mild strain when prying the faceplate off to keep away from damaging the gadget or surrounding surfaces.
- For those who encounter any resistance when eradicating the faceplate, cease and examine the realm for any obstacles or obstructions.
- For those who’re disconnecting the doorbell wire, be certain that to push down on the wire connector tab firmly to launch the wire.
| Step | Motion |
|---|---|
| 1 | Find and take away the screw utilizing a Phillips screwdriver. |
| 2 | Use a plastic pry instrument or flat-head screwdriver to rigorously pry off the faceplate. |
| 3 (non-compulsory) | If transferring the doorbell, disconnect the doorbell wire by urgent down on the wire connector tab and pulling out the wire. |
Detach the Mounting Bracket
Step one in eradicating your Ring Doorbell Professional is to detach the mounting bracket. To do that, you’ll need to take away the 2 screws which can be situated on the underside of the bracket. As soon as the screws are eliminated, you’ll be able to gently pull the bracket away from the wall.
For those who discover that the bracket is caught, you need to use a screwdriver or a pair of pliers to softly pry it unfastened. Watch out to not harm the bracket or the wall when doing this.
As soon as the bracket is indifferent, you’ll need to disconnect the wires which can be related to the doorbell. To do that, merely use your fingers to pinch the terminals on the again of the doorbell and pull the wires out.
Here’s a desk that summarizes the steps concerned in detaching the mounting bracket:
| Step | Motion |
|—|—|
| 1 | Take away the 2 screws which can be situated on the underside of the bracket. |
| 2 | Gently pull the bracket away from the wall. |
| 3 | If the bracket is caught, use a screwdriver or a pair of pliers to softly pry it unfastened. |
| 4 | Disconnect the wires which can be related to the doorbell. |
Disassemble the Energy Package
The Energy Package is the a part of the Ring Doorbell Professional that connects the doorbell to your own home’s electrical system. To take away the Ring Doorbell Professional, it’s essential to first disassemble the Energy Package that connects the doorbell to the wiring of your own home. This is the best way to do it:
- Flip off the ability to your doorbell on the circuit breaker or fuse field.
- Take away the 2 screws that maintain the faceplate of the Energy Package in place.
- Pull the faceplate straight out from the wall.
- Contained in the Energy Package, you will note 4 wires:
- As soon as the wires are disconnected, you’ll be able to take away the Energy Package from the wall.
| Wire | Description |
|---|---|
| White | Impartial wire |
| Black | Scorching wire |
| Inexperienced | Floor wire |
| Crimson | Energy wire |
Disconnect the wires from the Energy Package by loosening the screws on the wire terminals. Ensure to recollect which wire was related to which terminal.
Uninstall the Electrical Wires
Step 1: Flip off the ability to your Ring Doorbell Professional on the circuit breaker or fuse field. It is a essential security measure to stop electrical shocks.
Step 2: Take away the faceplate of your Ring Doorbell Professional by unscrewing the 2 safety screws situated on the backside of the gadget.
Step 3: Disconnect the wires from the Ring Doorbell Professional terminals. Observe the positions of the wires (normally labeled “FRONT” and “REAR”) so you’ll be able to reconnect them accurately later.
Step 4: Use a screwdriver or wire strippers to loosen the terminal screws and thoroughly take away the wires.
Step 5: Pull the wires gently out of the wall to create some slack. You could want to make use of a pair of needle-nose pliers to grip the wires securely.
| Rear | Entrance |
|---|---|
| White wire (-) | Black wire (+) |
Step 6: Tape the ends of the wires collectively utilizing electrical tape to stop them from touching and creating a brief circuit.
Step 7: Tuck the wires again into the wall and safe them with electrical tape or wire nuts.
Step 8: Restore energy to your Ring Doorbell Professional by turning the circuit breaker or fuse again on.
Take away the Chime Package (If Put in)
For those who’ve put in a Ring Doorbell Professional with a chime equipment, you may have to take away it earlier than continuing. This is how:
Step 1: Find the chime equipment.
It is sometimes mounted on a wall close to an current doorbell chime.
Step 2: Flip off energy to the chime equipment.
Flip the breaker that controls the chime equipment’s circuit or take away the fuse.
Step 3: Disconnect the chime equipment from the wall.
Use a screwdriver to take away the screws holding it in place.
Step 4: Disconnect the wires from the chime equipment.
Take an image of the wiring configuration earlier than disconnecting any wires. It will enable you rewire the chime equipment later if wanted.
Step 5: Take away the chime equipment from the wall.
As soon as the wires are disconnected, you’ll be able to pull the chime equipment away from the wall and take away it fully.
Step 6: Cap the uncovered wires.
Utilizing electrical tape or wire nuts, cap the uncovered wires on the wall and on the chime equipment. It will stop electrical shocks and brief circuits.
| Wire Shade | Connection |
|---|---|
| Crimson | Transformer terminal (constructive) |
| Black | Transformer terminal (damaging) |
| White | Entrance doorbell button |
| Yellow | Rear doorbell button (if relevant) |
Reset the Ring Doorbell Professional
Step 1: Take away the Faceplate
Gently pry off the faceplate protecting the doorbell’s buttons and digital camera.
Step 2: Find the Reset Button
Contained in the doorbell, discover the small, black reset button situated close to the underside.
Step 3: Insert a Pin
Use a small pin or paperclip to softly press and maintain the reset button for 15 seconds.
Step 4: Launch the Button
After 15 seconds, launch the reset button.
Step 5: Await the Blue Ring
The doorbell will flash a blue ring across the button to point it’s resetting.
Step 6: Reinstall the Faceplate
As soon as the blue ring has stopped flashing, substitute the faceplate over the doorbell.
Step 7: Reconfigure the Doorbell
a) Open the Ring App
Launch the Ring app in your smartphone and log in to your account.
b) Choose the Doorbell
Select the Ring Doorbell Professional you wish to reconfigure from the listing of gadgets.
c) Comply with the Prompts
Comply with the on-screen directions within the app to reconnect your doorbell to Wi-Fi and full the setup course of.
Confirm Profitable Removing
After getting accomplished the steps above, it is essential to confirm that the Ring Doorbell Professional has been efficiently eliminated. This is how:
Checking the Ring App
Open the Ring app in your cellular gadget. If the Ring Doorbell Professional has been eliminated efficiently, it would now not seem within the listing of gadgets.
Checking Your Gateway
When you’ve got a Ring Chime Professional or Ring Chime, it would present a blue mild when the Ring Doorbell Professional is related. If the Ring Doorbell Professional has been eliminated efficiently, the blue mild on the Gateway will flip off.
Checking for Bodily Disconnection
Go to the place the Ring Doorbell Professional was put in. If it has been eliminated efficiently, the doorbell will now not be bodily related to the wiring.
Troubleshooting
For those who’ve adopted the steps above however the Ring Doorbell Professional remains to be showing within the Ring app or the Gateway remains to be displaying a blue mild, attempt the next:
- Just remember to have accomplished all of the steps within the elimination course of.
- Restart the Ring Doorbell Professional by urgent the orange button on the again of the gadget.
- Restart the Ring app in your cellular gadget.
- Contact Ring help for additional help.
Clear the Mounting Space
Earlier than eradicating your Ring Doorbell Professional, it is essential to scrub the mounting space to stop any residue or grime from affecting the set up course of. This is the best way to clear it successfully:
1. Collect the Vital Instruments
You will want a tender fabric, rubbing alcohol, and a screwdriver or drill.
2. Flip Off the Energy
Change off the breaker or fuse that powers the doorbell to make sure security.
3. Take away the Faceplate
Use a screwdriver to unscrew the 2 screws on the backside of the faceplate and elevate it off the bottom.
4. Clear the Base
Wipe down the bottom of the doorbell with a tender fabric dampened with rubbing alcohol. Ensure to take away any grime or particles.
5. Clear the Mounting Floor
Utilizing a humid fabric, wipe down the realm the place the doorbell was mounted to take away any grime or residue. Guarantee it is fully dry earlier than persevering with.
6. Take away the Mounting Plate
Unscrew the 4 screws that safe the mounting plate to the mounting floor. Fastidiously elevate the plate off.
7. Clear the Screws
Wipe down the screws with rubbing alcohol to take away any grime or particles.
8. Examine the Seal
Verify the rubber seal across the mounting plate. If it is broken or worn, substitute it earlier than putting in the brand new doorbell.
9. Clear the Wires
For those who’re changing the doorbell with a wired mannequin, clear the wires utilizing rubbing alcohol. Guarantee they’re freed from grime or corrosion. You may as well use a wire brush to take away any cussed residue or oxidation.
| Supplies | Utilization |
|---|---|
| Gentle fabric | Wiping surfaces |
| Rubbing alcohol | Cleansing surfaces and wires |
| Screwdriver or drill | Eradicating screws |
Safe the Gap or Wires
As soon as the doorbell is disconnected, it’s essential to safe the outlet the place it was mounted. For those who do not, water, bugs, or different particles can enter your own home by way of the opening. There are just a few methods to do that, relying on the kind of floor the doorbell was mounted on.
If the doorbell was mounted on brick or concrete:
- Fill the outlet with a silicone or polyurethane caulk utilizing a caulk gun.
- Clean the caulk together with your finger or a putty knife.
- Enable the caulk to dry fully, which can take a number of hours or days, relying on the kind of caulk used.
If the doorbell was mounted on wooden:
- Minimize a small piece of wooden to suit over the outlet.
- Glue or nail the wooden piece into place.
- Paint or stain the wooden piece to match the encompassing space.
If the doorbell was mounted on vinyl siding:
- Take away the siding panel that the doorbell was mounted on.
- Minimize a chunk of scrap siding to suit over the outlet.
- Glue or nail the scrap siding into place.
- Reinstall the siding panel.
If the doorbell was mounted on a floor apart from brick, concrete, wooden, or vinyl siding:
- Seek the advice of with a house enchancment skilled for recommendation on one of the simplest ways to safe the outlet.
Along with securing the outlet, you additionally have to handle the wires that have been related to the doorbell. If the wires should not correctly insulated, they might change into a fireplace hazard. Minimize the wires near the doorbell after which wrap them with electrical tape or cowl them with wire nuts.
Learn how to Take away a Ring Doorbell Professional
To take away a Ring Doorbell Professional, observe these steps:
1.
Flip off the ability to your doorbell by flipping the breaker or eradicating the fuse.
2.
Take away the faceplate by unscrewing the 2 screws on the backside.
3.
Disconnect the wires from the terminals on the again of the doorbell.
4.
Take away the 2 screws which can be holding the doorbell in place.
5.
Pull the doorbell straight out of the wall.
Individuals Additionally Ask About Eradicating a Ring Doorbell Professional
Learn how to take away a Ring Doorbell Professional that’s hardwired?
In case your Ring Doorbell Professional is hardwired, you’ll need to disconnect the wires from the terminals on the again of the doorbell earlier than you’ll be able to take away it. To do that, use a small screwdriver to loosen the screws on the terminals after which pull the wires off.
Learn how to take away a Ring Doorbell Professional that’s battery-powered?
In case your Ring Doorbell Professional is battery-powered, you’ll need to take away the battery earlier than you’ll be able to take away the doorbell. To do that, use a small screwdriver to loosen the screw on the underside of the doorbell after which pull the battery out.
